13 Plastic Cement is a scientifically compounded composition of selected asphalts, mineral fillers and refined solvents that are manufactured to a heavy consistency for application by trowel to provide a durable, elastic coating of excellent adhesion and high resistance to water and weathering. This product, when applied dries to a tough, flexible, waterproof and corrosion proof coating, which gives excellent performance over wide ranges of temperature and weather conditions. 13 Plastic Cement is available in 2 consistencies: Summer and Winter Grade
55 gallon drums
5 gallon pails
Will not shrink or crack
Smooth, easy to apply rubber-like trowel consistency
Excellent adhesion
Excellent resistance to flow (sag) at high roof temperatures
Ready to apply – no mixing required
Will not shrink or crack
Smooth, easy to apply rubber-like trowel consistency
Excellent adhesion
Excellent resistance to flow (sag) at high roof temperatures
Ready to apply – no mixing required
13 Plastic Cement is a general-purpose cement for repairing leaks in shingles, concrete, metal or asphalt roofs, flashings on walls, chimneys, flues, downspouts and cornices. Excellent for sealing cracks in concrete, brick, as a joint filler for pre-cast roof slabs and general-purpose use in maintenance of exposed buildings and structures.
1. Consistency: A smooth, heavy trowel consistency that will readily spread on
and adhere to most all surfaces without sagging.
2. Character of Dried Film: Uniform, excellent adhesion to masonry, steel, slab
insulation and other surfaces.
3. The dried film retains its flexibility and ductility so that the coating will resist
extreme variations in temperature and weather.
4. Has excellent resistance to flow at high temperatures when used on a
vertical surface.
SURFACE PREPARATION:
All surfaces should be dry, clean and free from oil or grease, dust, dirt, loose paint
or other foreign matter.
APPLICATION:
Spread 13 Plastic Cement to an average thickness of 1/8” (approximately 8 gallons per square) and press tightly into joints, seams or cracks. To repair large
cracks, breaks and blisters, spread 13 Plastic Cement over the damaged area then embed 34 Cotton, 31 Fiberglass or 3036 Polyester membrane reinforcement and then apply another layer of 13 Plastic Cement over the entire patch.
COVERAGE RATE:
Apply each application at an average thickness of 1/8” (8 gallons per 100 sq. ft.)
Do not use near open flame. Avoid breathing solvent fumes and prolonged contact with skin. Do not take internally. If swallowed, do not induce vomiting. Call a physician immediately. Keep out of reach of children. Store in a heated room and keep container covered when not in use. Do not thin. Dispose of in an environmentally safe manner. Cover air intakes during application and while drying. Exterior use only.
Will not shrink or crack
Smooth, easy to apply rubber-like trowel consistency
Excellent adhesion
Excellent resistance to flow (sag) at high roof temperatures
Ready to apply – no mixing required
13 Plastic Cement is a general-purpose cement for repairing leaks in shingles, concrete, metal or asphalt roofs, flashings on walls, chimneys, flues, downspouts and cornices. Excellent for sealing cracks in concrete, brick, as a joint filler for pre-cast roof slabs and general-purpose use in maintenance of exposed buildings and structures.
1. Consistency: A smooth, heavy trowel consistency that will readily spread on
and adhere to most all surfaces without sagging.
2. Character of Dried Film: Uniform, excellent adhesion to masonry, steel, slab
insulation and other surfaces.
3. The dried film retains its flexibility and ductility so that the coating will resist
extreme variations in temperature and weather.
4. Has excellent resistance to flow at high temperatures when used on a
vertical surface.
SURFACE PREPARATION:
All surfaces should be dry, clean and free from oil or grease, dust, dirt, loose paint
or other foreign matter.
APPLICATION:
Spread 13 Plastic Cement to an average thickness of 1/8” (approximately 8 gallons per square) and press tightly into joints, seams or cracks. To repair large
cracks, breaks and blisters, spread 13 Plastic Cement over the damaged area then embed 34 Cotton, 31 Fiberglass or 3036 Polyester membrane reinforcement and then apply another layer of 13 Plastic Cement over the entire patch.
COVERAGE RATE:
Apply each application at an average thickness of 1/8” (8 gallons per 100 sq. ft.)
Do not use near open flame. Avoid breathing solvent fumes and prolonged contact with skin. Do not take internally. If swallowed, do not induce vomiting. Call a physician immediately. Keep out of reach of children. Store in a heated room and keep container covered when not in use. Do not thin. Dispose of in an environmentally safe manner. Cover air intakes during application and while drying. Exterior use only.